Security Command XR200 Guia de Instalação Página 29

  • Descarregar
  • Adicionar aos meus manuais
  • Imprimir
  • Página
    / 32
  • Índice
  • MARCADORES
  • Avaliado. / 5. Com base em avaliações de clientes
Vista de página 28
Digital Monitoring Products XR200 Installation Guide
22
WIRING DIAGRAMS
XR200 Installation Guide Digital Monitoring Products
23
WIRING DIAGRAMS
20.5 Remote Station Reversing Relay Connection
AC
1
2
3
4 5 6 7
8
10
11 12 13 14
15
16 17 18
19
9
20
21
22 23
24
25
26 27
28
+B
BELL
GND
SMK
GND
RED
YEL
GRN
BLK
Z1
Z2 Z3 Z4
Z5
Z6
Z7
Z8 Z9+
Z9-
Z10+
Z10-
AC
-B
GND
GND
GND
GND
XR200 Command Processor™ Panel
J3
DD, MPX
Selection
Headers
J4
Tamper
Header
J2 Output Header
J10
J16
Panel
Reset
J11J12
462N Network Interface Card
+ -
+
-
Black
Red
+ -
+
-
Black
Red
S
Alternate Alarm
Combo Alarm
Auxiliary Power In
+ Signal Voltage In
+ To Remote Receiver
- To Remote Receiver
- Signal Voltage In
EARTH GROUND
GROUND
GROUND
Up to 60 hours of battery standby time can be supplied
using three or four 7.7Ah, sealed, Lead-Acid batteries.
Four 7.7Ah batteries may be required based on total current
draw of all devices connected to the panel. See section
Standby Battery Calculations.
To connect four batteries to the XR200 Command
Processor™ Panel, use three Model 318 Battery Harnesses.
Reversing Relay Module
Radionics Model D127
5mA Standby, 55mA Alarm
@12 VDC
Alternate Alarm
Combo Alarm
Auxiliary Power In
+ Signal Voltage In
+ To Remote Receiver
- To Remote Receiver
- Signal Voltage In
EARTH GROUND
GROUND
GROUND
Reversing Relay Module
Radionics Model D127
5mA Standby, 55mA Alarm
@12 VDC
S
To Telephone Line
To Telephone Line
J2 Output Header
All outputs must be located
within the same room as
the control panel.
K2 K4
K6 K7
Relay Output 1
Use Model 305
Relay Output 2
Use Model 305
Answering Machine
Bypass Relay
Use Model 305
Ground Start Relay
Use Model 305
Model 430
Output Harness
S
= Supervised Circuit
Intended for connection to a
polarity reversal circuit of a
remote station receiving unit
having compatible ratings.
All modules must be installed in a
UL Listed enclosure connected by
no more than 20 feet of conduit.
Fire Alarm Output 3 -
White/Orange
Fire Trouble Output 4 -
White/Yellow
Outputs 3 through 6 supply
up to 50mA at 12 VDC.
Note: Output 3 must be programmed as a Fire Alarm
Output and Output 4 must be programmed as a Fire
Trouble Output. See Output Options section of the
XR200/XR2400F Programming Guide (LT-0196).
S
S
S
Vista de página 28
1 2 ... 24 25 26 27 28 29 30 31 32

Comentários a estes Manuais

Sem comentários

KRAM 84592M manuels

Manuels d'utilisation et guides de l'utilisateur pour Kits de voiture KRAM 84592M.
Nous fournissons des manuels en pdf 1 KRAM 84592M à télécharger gratuitement par type de document : Fiche technique


Kram 84592M Fiche technique (2 pages)


marque: Kram | Catégorie: Car kits | Taille: 0.97 MB |

 

Table des matières





Plus de produits et de manuels pour Kits de voiture KRAM

Modèles Type de document
84064M Fiche technique   KRAM 84064M car kit, 2 pages
84326 Fiche technique   KRAM 84326 car kit, 2 pages
67634 Fiche technique   KRAM 67634 car kit, 2 pages
84963M Fiche technique   KRAM 84963M car kit, 2 pages
84071 Fiche technique   KRAM 84071 car kit, 2 pages
86795 Fiche technique    KRAM 86102L car kit, 2 pages
90200 Fiche technique   KRAM 90200 car kit, 2 pages
68657 Fiche technique   KRAM 68657 car kit, 2 pages
84444 Spécifications   KRAM 84444 car kit, 2 pages
67735 Guide de dépannage   KRAM 67735 car kit, 2 pages
67656 Guide de dépannage   KRAM 67656 car kit, 2 pages
67675 Guide de dépannage   KRAM 67675 car kit, 2 pages
X660 Spécifications    KRAM X660 car kit, 2 pages
84063 Spécifications   KRAM 84063 car kit, 2 pages
84103X103M Spécifications   KRAM 84961X961 car kit, 2 pages
84070 Spécifications   KRAM 84070 car kit, 2 pages
84958 Spécifications   KRAM 84958 car kit, 2 pages
84612 Spécifications   KRAM 84612 car kit, 2 pages
X101 Spécifications    KRAM X101 car kit, 2 pages
67687 Guide de dépannage   KRAM 67687 car kit, 2 pages